You are now responsible for paying tax on all orders in the expired state(s).
Please visit the My Company page to upload an updated version to regain your tax exempt status.
By clicking the button below, you agree to paying tax in the expired state(s).
Please visit the My Company page to upload an updated version.
If you do not upload an updated version, you will forfeit your tax exemption status.
You are now responsible for paying tax on all orders in the invalid document state(s).
Please visit the My Company page to upload an updated version to regain your tax exempt status.
By clicking the button below, you agree to paying tax in the invalid document state(s).
Something went wrong while processing your request.
Please try again later.
WAVE Electronics is not responsible for any tax accrued on sales orders after tax certifications are expired.
It's been awhile. Please check the information below to ensure we have the most up to date information.
Account Number:
Contact Name:
Company Name:
Billing Address:
Something went wrong while processing your request.
Please try again later.
Thank you for updating your information.
We have sent an email to
to confirm the validity of the email address.
After receiving the email please confirm using the link provided to complete your update.
The third component in the in-wall subwoofer system is the IWA-250 switch mode amplifier: a slim, powerful dedicated design in a heavy-duty 1U rack mount case. Delivering up to 250 watts into 4 ohms, a single IWA-250 will power single or dual IWS-10s to provide higher power levels for larger rooms or to meet customer demands. The IWA-250 can be configured to switch on automatically using input signal sensing, or by using the preferred 12v trigger link from an AVR or system source. The IWA-250 will then automatically be switched on and off with the AVR, TV or system remote control handset.
The amplifier utilises a cool running Class D power stage driven by a PWM supply with integrated DSP. Filtering and functionality are controlled in the software for precise and reliable operation. The IWA-250 offers a choice of single LFE, balanced XLR and stereo RCA inputs. Output connection is made via two sets of push type terminals to provide connection to one or a pair of IWS-10 drivers. The front panel allows access to all control features for easy adjustment when fitted into a rack bay. An EQ switch offers a selection of music, movie and impact presets for the ideal response in-room. There is also an enclosure switch to calibrate the drive characteristics when the IWS-10 is used within or without the IWB-10 back box.
Features
Rigid, high quality steel case
Switch mode power supply
Class D power amplifier delivering up to 250watts into 4ohms (dual IWS-10 drivers)
High efficiency design resulting in cool running - low thermal output
DSP controlled with advanced limiters
<0.5watt standby power consumption (ErP certified)
DC short circuit protection, over-current and thermal protection
Specifications
Specifications:
System Format Active sub-woofer amplifier
Low Frequency Limit 25Hz
Upper Frequency Limit Variable 40 - 120 Hz @ 24dB/Octave
Amplifier Power Output 250W @ < 1% THD+N
Drive Unit Parameters 4 - 8 Ohm Nominal Impedance
Amplifier Classification Class D amplifier with Switch mode power supply (SMPSU)
Cabinet Switch For use when using the dedicated back box
EQ Switch Music/ Movie/ Impact
Phase Control 0 & 180 degrees
Auto Sensing Line Level > 3.5mV
Input Level Requirements Standby after approximately 15 minutes if no signal sensed
Input Impedance > 20K Ohms
Mains Input Voltage: AC 110 - 120 V ~ 50/60Hz; AC 220 - 240 V ~ 50/60Hz (Factory Region Preset)
Dimensions (H x W x D) 43.7 x 432 x 263mm; 1 3/4 x 17 x 10 3/8 Inch
Connections LFE in (Stereo RCA and Balanced), 12v Trigger in (3.5mm mono mini-jack), left and right speaker output
12v Trigger Input 5 - 12v via 3.5mm mono mini-jack socket
Power Consumption: Standby: < 0.5W (ErP approved); Typical Idle: < 10W; Max Rated: 200W
Weight (unpacked 4Kg (8lb 12oz